main.py

@@ -7,25 +7,17 @@
 import serial
 import time
 
-ser = serial.Serial('/dev/ttyACM0', baudrate = 9600, timeout = 6)
+ser = serial.Serial('/dev/ttyACM0', baudrate = 9600, timeout = 1)
 
 #time.sleep(3)
 
-#ser.readline()
-while 1:
-#    ser.readline()
-    Data = ser.readline().decode('ascii')
-    print(Data)
-    #outFile = open("arduino-fridge-powercontrol.json", "w")
-    #outFile.write(Data)
-    #outFile.close
 
-##while 1:
-##    # {  "command": "switch",  "arg": "one",  "state": "off", "ver":"1690931931"}
-##    userInput = input('> ')
-##    ser.write(str(userInput).encode('ascii'))
-##    arduinoData = ser.readline().decode('ascii')
-##    print(arduinoData)
+while 1:
+    # {  "command": "switch",  "arg": "one",  "state": "off", "ver":"1690931931"}
+    userInput = input('> ')
+    ser.write(str(userInput).encode('ascii'))
+    arduinoData = ser.readline().decode('ascii')
+    print(arduinoData)
 
 
 ##def getValues():

main/main.ino

@@ -36,20 +36,66 @@ bool fetState2;
 
 uint8_t addrSensor1[8] = { 0x28, 0xFF, 0x64, 0x1F, 0x79, 0xD1, 0xB1, 0x75 };
 uint8_t addrSensor2[8] = { 0x28, 0xFF, 0x64, 0x1F, 0x79, 0xD7, 0xDA, 0x9A };
+/*
+
+// countLowTemp
+int cLTemp1 = 0;
+int cLTemp2 = 0;
+// countHighTemp
+int cHTemp1 = 0;
+int cHTemp2 = 0;
+// loops to count temp before switching state
+int cTemp = 5;
+
+*/
 
 void setup() {
   // put your setup code here, to run once:
   pinMode(MOSFET1, OUTPUT);
   pinMode(MOSFET2, OUTPUT);
 
+ 
   Serial.begin(9600);
   sensors.begin();
 
+  // locate devices on the bus
+  Serial.println("Locating devices...");
+  Serial.print("Found ");
+  deviceCount = sensors.getDeviceCount();
+  Serial.print(deviceCount, DEC);
+  Serial.println(" devices.");
+  Serial.println("");
+  
+  Serial.println("Printing addresses...");
+  for (int i = 0;  i < deviceCount;  i++)
+  {
+    Serial.print("Sensor ");
+    Serial.print(i+1);
+    Serial.print(" : ");
+    sensors.getAddress(Thermometer, i);
+    printAddress(Thermometer);
+  }
+
+  Serial.println("");
+  Serial.print("MOSFET1 start temp: ");
+  Serial.print(HTemp1);
+  Serial.print("°C, stop temp: ");
+  Serial.print(LTemp1);
+  Serial.println("°C");
+  Serial.print("MOSFET2 start temp: ");
+  Serial.print(HTemp2);
+  Serial.print("°C, stop temp: ");
+  Serial.print(LTemp2);
+  Serial.println("°C");
 }
 
 void loop() {
+  // put your main code here, to run repeatedly:
+
+//if(Serial.available()>0) {
 
   sensors.requestTemperatures(); 
+
   
   tempSensor1 = sensors.getTempC(addrSensor1);
   if(tempSensor1 > HTemp1) {
@@ -69,16 +115,56 @@ void loop() {
     fetState2 = 0;
   }
 
+
+  /*
+  Serial.print("Sens 1 ");  
+  Serial.print("Celsius temperature: ");
+  // Why "byIndex"? You can have more than one IC on the same bus. 0 refers to the first IC on the wire
+  Serial.print(sensors.getTempC(addrSensor1)); 
+  Serial.print(" - Fahrenheit temperature: ");
+  Serial.print(sensors.getTempF(addrSensor1));
+  Serial.print(" - MOSFET1 Sate: ");
+  Serial.println(fetState1);
+
+  Serial.print("Sens 2 ");  
+  Serial.print("Celsius temperature: ");
+  // Why "byIndex"? You can have more than one IC on the same bus. 0 refers to the first IC on the wire
+  Serial.print(sensors.getTempC(addrSensor2)); 
+  Serial.print(" - Fahrenheit temperature: ");
+  Serial.print(sensors.getTempF(addrSensor2));
+  Serial.print(" - MOSFET2 Sate: ");
+  Serial.println(fetState2);
+  */
+
   StaticJsonDocument<96> jsonOut;
   //jsonOut["sensor"] = "1";
-  jsonOut[0]["temp"] = tempSensor1;
-  jsonOut[0]["state"] = fetState1;
+  jsonOut["sensor1"]["temp"] = tempSensor1;
+  jsonOut["sensor1"]["state"] = fetState1;
 
   //jsonOut["sensor"] = "2";
-  jsonOut[1]["temp"] = tempSensor2;
-  jsonOut[1]["state"] = fetState2;
+  jsonOut["sensor2"]["temp"] = tempSensor2;
+  jsonOut["sensor2"]["state"] = fetState2;
   serializeJson(jsonOut, Serial);
-  
-  delay(5000);
+  Serial.println();
+  /*
+  digitalWrite(MOSFET, HIGH);
+  delay(2000);
+  digitalWrite(MOSFET, LOW);
+  delay(2000);
+  */
+  delay(1000);
+//  }
   
 }
+
+void printAddress(DeviceAddress deviceAddress)
+{ 
+  for (uint8_t i = 0; i < 8; i++)
+  {
+    Serial.print("0x");
+    if (deviceAddress[i] < 0x10) Serial.print("0");
+    Serial.print(deviceAddress[i], HEX);
+    if (i < 7) Serial.print(", ");
+  }
+  Serial.println("");
+}